• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

Living Holds

All about living product reviews & buying guide

  • Blog
  • Garden Tools
  • Hand Tools
  • Home Tools
  • Power Tools

7 Easy Tips for Cutting Small Circles with A Router

Last Updated: July 18, 2019 | David Watson

With the use of a router, one could practice numerous forms to the rims of a chunk of wood. Many routers are flexible enough to use wholly or partly to assist shape in different forms. We have mentioned 7 tips for cutting small circles with a router, let’s have a look at them.

cutting small circles with a router

First of all, a router is a strong tool of power for the contemporary shops of wood. Or in an another format- router is a most perfect tool for cutting circles in wood. Most woodworkers could have at least 2 to 3 types of routers of numerous levels of horsepower base.

Tips for Cutting Circles with A Router

This article will provide you with a few tips and tricks to create a perfect circle with a router.

1. Install Router Bits Properly for Longer Use

Since numerous router bits are capable of following an extensive assortment of forms to the edge of a chunk of wood. Therefore, the router bits will not be able to cut in a proper way if they are not set up into the band of the router efficiently.

A badly set up bit can reverberate extremely (known as chatter) which will produce a difficult profile. However, might be pretty risky sometimes. In contrast to it, setting up the router bits properly will come in handy for a longer period toward the usage of the router effectively and correctly.

2. Avoiding the Breakage of Wood While Routing

While cutting woods are subjected to breaking up, it will however, work certainly if the router is routed with the wood rather than using against it. This problem may occur again when someone routes the end of the wood.

Therefore, it is necessary to trim the edges of the wood first. The tear-out on the sides will probably be wiped up whilst cutting the side edges of the wood.

Hence, put a scrap material at the side of the wood. If the bit maintains beyond the work on another block, it will certainly not break off the edges of the wood.

3. The Better Way to Cut Small Circles

It’s tough to hold thin or small wood from breaking off while it is in the stage of cutting at the router desk. Therefore, for delicate shapes which includes the cut of the circles, it is safer and less difficult to route on a huge board first, and then, cutting off the circled area.

4. A Smooth Circle Without Chips

The spiral bit cuts frequently make a simple and precise cuts than straightened bits. Since spiral bit in upward direction pulls the chips up and then taking them out, making it best for cutting coherence even in solid wood.

Also, a bit cut in downward direction lowers chip downward, which is perfect for making smooth circles in the wood. Down cut are essentially recommended for round shapes.

Furthermore, a squeezed bit has spirals strolling in two ways, that are up and down. They  pull chips closer to the center of the bit.

5. Step Up for An Easier Start

When there is a creation of a template for routing pattern, make certain to add a starting ramp. Due to the fact that this presents a secure area for the bit of the router to make a connection with the template earlier than it starts to cut off. Finally, put on an exit ramp at the other side of the template as well.

6. Shallow Cut before Cutting Deeply

First of all, while routing in a bit of wood to cut out a smooth and round circle, the first step is to cut the surface shallow rather than cutting it deeply. This will assist to shield the motor of the router but the cutting blades of the router as well.

Keep in mind that the circle in the wood will come down, when the last pass gets done through the wood. Therefore, to prevent the wood from becoming attached to the cutter as when the contact ends between them, comfy it with a tape.

7. Marking is Important

The most noteworthy thing is to create an outline of the circle on the wood. So as to mitigate the risk of cutting a harsh circle. Furthermore, this will assist to make certain that the cut is smooth and nice, and might assist in placing the router at the center.

Conclusion

Following the above-mentioned tips will help in cutting small circles with a router to get even and smooth circles in wood. So you can follow these steps to get a good result in your cutting. 🙂 We hope you love the article. So don’t forget to share it with your friends.

Similar Article: Cut A Circle in Wood with A jigsaw Step by Step Guide.

Filed Under: Blog, Hand Tools

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recently Reviewed Buying Guide

  • Best Tiller for Breaking New Ground 2021 – Reviews & Buying Guide
  • Best Refrigerator Water Filter Reviews 2021 & Buying Guide
  • Best Tool for Cutting Circles in Wood 2021 – Reviews & Buying Guide
  • Best Mini Split Air Conditioner Reviews 2021 & Buying Guide

Copyright © 2022 · Living Holds · All rights reserved.

Featured on Hometalk.com DMCA.com Protection Status

My website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.